About the Equipment
- 外观尺寸: W1,180×L1,070×H855mm
- 炉内尺寸: φ715×H455mm（0.18M3）
- 炉壁厚度: 140mm
- 重量: 185kg
- 电功率: 11.5kw
- 电量: 单相 220V・53A
- 最高烧成温度: 1300℃
- 附件:
- 电热偶: R 型电热偶, 1 个
- 棚板: φ650mm（半圆）6块
- 支柱: 30, 60, 90, 120, 150, 210mm 各6个
- 必须采用电脑智能控温系统控制烧成，内设不少于10种基本烧成程序: 干燥200℃、试车400℃、素烧700℃、烤花800℃，釉烧1220℃、釉烧1230℃、釉烧1240℃、釉烧1250℃、釉烧1260℃、釉烧1270℃，打开电窑空气开关后按不超过3个按键就能够快速启动内设基本烧成程序。电脑智能控温系统能够设置1～4个阶段自编烧成程序和1～16个阶段的自编连续烧成程序，每个阶段以目标烧成温度以及达到烧成温度所需要的分钟数来进行设定,能够控制不同烧成阶段的升温、降温速度。必须具有保温设定功能，能够对各个阶段的目标温度进行保温时长设定，单位为分钟，以达到烧制陶瓷（或者玻璃）的烧成要求。电脑智能控温系统必须能够存储不少于20个自编烧成程序。打开电窑空气开关后按不超过3个按键就能够快速启动自编烧成程序。简单易操作。
- 必须能够设定以下三种蜂鸣器:
- a: 设定蜂鸣器静音。
- b: 以设定烧成程序的指定温度设定蜂鸣器鸣响.
- c: 以设定烧成程序结束后设定蜂鸣器鸣响。
- 电脑智能控温系统必须具有按键锁定功能，以防止在烧成过程中外来人员或者学生进行误操作，威胁人身安全。电脑智能控温系统必须具有延时烧制设置功能、方便使用者定时烧成，有效错开高峰期用电等因素。电脑智能控温系统必须带有安全·报错功能：出现以下情况电脑智能控温系统能够立即停止烧成、电脑基板显示错误报告，有效预防安全事故的发生。
- ①窑炉温度不能上升
- ②热电偶或导线断线或检测出异常高温
- ③热电偶接反、电脑智能控温系统温度异常
- ④温度传感器故障。
- 耐火材质: 窑炉高温
- External dimensions: W1,180×L1,070×H855mm
- Inside size: φ715×H455mm (0.18M3)
- Wall thickness: 140mm
- Weight: 185kg
- Power: 11.5kw
- Electric power: 11.5kw Single-phase 220V・53A
- Maximum Firing Temperature: 1300°C
- Accessories.
- Thermocouple: R-type thermocouple, 1 pc.
- Scaffolding board: φ650mm (semi-circular) 6 pieces
- Pillar: 30, 60, 90, 120, 150, 210mm each 6pcs.
- Must adopt computerized intelligent temperature control system to control the firing, with no less than 10 kinds of basic firing programs: drying at 200℃, test drive at 400℃, plain firing at 700℃, baking at 800℃, glaze firing at 1220℃, glaze firing at 1230℃, glaze firing at 1240℃, glaze firing at 1250℃, glaze firing at 1260℃, glaze firing at 1270℃, and it is possible to quickly start the built-in basic firing programs by pressing no more than 3 buttons after turning on the kiln's air switch. Quickly start the built-in basic firing program. Computer intelligent temperature control system can be set up 1 to 4 stages of self-programmed firing program and 1 to 16 stages of self-programmed continuous firing program, each stage to the target firing temperature and the number of minutes to reach the firing temperature to be set to control the different stages of the firing of the heating, cooling speed. Must have a heat preservation setting function, can be the target temperature of each stage of the heat preservation time setting, the unit is minutes, in order to achieve the firing of ceramics (or glass) firing requirements. The computer intelligent temperature control system must be able to store no less than 20 self-programmed firing programs. The self-programmed firing program can be started quickly by pressing no more than 3 buttons after turning on the kiln air switch. Simple and easy to operate.
- It must be possible to set the following three buzzers.
- a: Mute the buzzer.
- b: Set the buzzer to sound at the specified temperature of the program.
- c: Set the buzzer to sound at the end of the firing program.
- Intelligent computer temperature control system must have a key lock function, in order to prevent the firing process of outsiders or students to misuse, threatening personal safety. Intelligent computerized temperature control system must have a delayed firing setup function to facilitate the user timed firing, effectively stagger the peak period of electricity consumption and other factors. Computerized intelligent temperature control system must be equipped with safety - error reporting function: the following situations occur computerized intelligent temperature control system can immediately stop firing, the computer baseboard displays an error report, effectively preventing the occurrence of safety accidents.
- ①The temperature of the kiln can not rise
- ② thermocouple or wire broken or abnormal high temperature detected
- ③Thermocouple connection is reversed, the temperature of the computerized intelligent temperature control system is abnormal.
- ③Thermocouple connection reversed, computerized intelligent temperature control system temperature abnormality
- ④Temperature sensor failure.
- Fire-resistant material: kiln high temperature